LCR Meter 4310 4320 4350 43100 - Wayne Kerr Electronics Asia

LCR Meters - 4310 4320 4350 and 43100

Comprehensive measurement functions, including DC resistance (Optional)
Test components from 20Hz to 1 MHz (43100)
0.1% basic accuracy
Drive level from 10mV to 2Vrms
Internal and external DC Voltage bias
GPIB / IEEE-488 and RS-232 interface
LCD display, with easy-to-read characters
Protection against charged capacitors
Small size and light weight

Data Sheet

A range of easy to use LCR meters with comprehensive measurement functions.

Accurate and fast measurements may be made from 20Hz to 1MHz (43100) making the 4300 series the ideal choice for many applications in the test or production environments.

All 4300 series instruments may be externally controlled using the standard RS232 or GPIB interfaces.

Technical Specifications

Measurement parameters

Any of the following parameters can be measured and displayed:

Impedance (Z)             Phase Angle (Ө)
Capacitance (C)          Dissipation Factor (D)
Inductance (L)             Quality Factor (Q)
AC Resistance (Rac)   Reactance (X)
Susceptance (B)         Conductance (G)
Admittance (Y)

DC Resistance (Rdc) is an option (/R) on all models.

Series/parallel equivalent circuit

Any combination

Polar Form

Z + Ө, Y + Ө

Test conditions

Frequency range

4310       20 Hz to 100 kHz
4320       20 Hz to 200 kHz
4350       20 Hz to 500 kHz
43100     20 Hz to 1 MHz

Frequency steps

5 Hz       20 Hz to 1 kHz
50 Hz       1 kHz to 10 kHz
500 Hz    10 kHz to 100kHz
5 kHz    100 kHz to 1MHz

Drive level (AC measurements)

Open circuit:                     10 mV to 2V rms
Voltage step size:             10 mV (200 steps)
Short circuit:                     100 µA to 20 mA rms
Current step size:              100 µA (200 steps)
Signal source impedance: 100Ω

DC bias voltage (internal)

2 Vdc

DC bias voltage (external)

External supply of up to ±40 V may be connected via rear panel

Measurement ranges

Z, R, X     0.01 mΩ to >1 GΩ
Y, B, G       0.1 nS to >2 kS
L                   1 nH to >2 kH
C              0.01 pF to >1 F
D, Q           0.0001 to 9999.9
Phase Angle -180° to +180°
Rdc           0.1 mΩ to >100 MΩ (Option)

Basic accuracy

0.1%
Varies with speed, frequency, AC drive level and impedance of Device Under Test.

Measurement speeds

Four selectable speeds for all measurement functions.
Up to 50 measurements per second depending on test frequency
and set up conditions.

Measurement connections

4 front panel BNC sockets
4-wire (Kelvin) measurements with screen at ground potential

Binning (optional)

User programmable PASS and FAIL bins. 25 way D-type interface connector.

Option /B1 (non-isolated)

Common 0V. Bin outputs 0 to 5V (nominal) with >10 mA current sink capability.

Option /B2 (isolated)

Common 24V input. Outputs 0 to 24V with >10 mA current source capability.

General

Power requirements

90 V AC to 264 V AC (Autoranging); 47 Hz to 63 Hz

Display

High contrast monochrome LCD module
320 x 240 with back lighting

Remote control

RS232 and GPIB (IEEE 488.2)

Mechanical

Height      104mm (4.1″)
Width       322mm (12.7″)
Depth       285mm (11.1″)
Weight         3kg (6.6lb)

Environmental conditions

Temperature Range

Storage -40°C to 70°C
Operating 0°C to 40°C
Full Accuracy 23°C ±5°C

Relative humidity

Up to 80% non-condensing

Altitude

Up to 2000m

Installation category

II in accordance with IEC664

Pollution degree

2 - mainly non-conductive

This equipment is intended for indoor use only in a non-explosive and non-corrosive atmosphere

Safety

Complies with the requirements of EN61010-1:2001

EMC

Complies with EN61326 for emissions and immunity

Order codes and options

4310 LCR Meter
20 Hz to 100 kHz 1J4310

4320 LCR Meter
20 Hz to 200 kHz 1J4320

4350 LCR Meter
20 Hz to 500 kHz 1J4350

43100 LCR Meter
20 Hz to 1 MHz 1J43100

All models supplied with User Manual, Kelvin clips and AC power cable.

Options

DC Resistance (Rdc) add /R to part number

Bin handler - non-isolated
(cannot be fitted with /B2) add /B1 to part number

Bin handler - isolated 24V
(cannot be fitted with /B1) add /B2 to part number

Accessories

Kelvin clips (fine jaws) 1EVA40150

Kelvin clips (large jaws) 1EVA40180

BNC to 4-terminal component fixture 1EV1006

4-terminal lead set 1EV1505

SMD Probe Lead 1EV1905A

SMD Tweezers 1EVA40120

Operating manual 9H4300

Certificate of Calibration with results 1JCALRES